RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: invertmast
Showing results 1 to 25 of 41
Search took 0.02 seconds.
Forum: RC Jets
02-22-2021, 06:53 PM
Replies: 978
Views: 200,484
Posted By invertmast

I feel your frustration Gary! Atleast your still...

I feel your frustration Gary! Atleast your still making progress, however slow it may be.

its amazing how much of a difference those hi-flow valves make on the retraction violence of the gear. I...
Forum: RC Jets
02-16-2021, 08:07 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, for your strut dilemna, have you looked...

Gary,
for your strut dilemna, have you looked into the high-hold “cone point” setscrews? They have either a 90* or 118* “point” on the end of them that when set into a drilled recess on the...
Forum: RC Jets
02-10-2021, 08:35 PM
Replies: 978
Views: 200,484
Posted By invertmast

I would recommend a reamer as well. Or if your...

I would recommend a reamer as well. Or if your lucky and the pivot pins are within a few .00x’s of a Letter/number/fractional/metric drill bit size, you could probly get by with using one of those...
Forum: RC Jets
02-04-2021, 09:16 AM
Replies: 978
Views: 200,484
Posted By invertmast

I did 3D print one on my SLA machine. I...

I did 3D print one on my SLA machine. I responded to your PM with specifics.
Forum: RC Jets
02-02-2021, 08:32 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, i was having a similar issue with the...

Gary,
i was having a similar issue with the gear on my big 40% Cessna 310. I found that the ramp for the uplock was a little gritty and a little too tight on the retraction slider bar. I cleaned...
Forum: RC Jets
12-18-2020, 09:25 AM
Replies: 978
Views: 200,484
Posted By invertmast

Looking good Gary! i just converted the...

Looking good Gary!

i just converted the retracts in my 40% cessna 310 over to 5/32 (4mm) airlines. Even with only using a 1/16” airline between standard nipple air tanks, the landing gear is...
Forum: RC Jets
09-30-2020, 06:06 PM
Replies: 978
Views: 200,484
Posted By invertmast

Looking goos Gary! How much servo wire have you...

Looking goos Gary! How much servo wire have you gone through so far, 50-60’? Haha
Forum: RC Jets
09-23-2020, 05:16 PM
Replies: 978
Views: 200,484
Posted By invertmast

Acetone will soften the CA. A Q-tip works well...

Acetone will soften the CA. A Q-tip works well for application to a specific spot
Forum: RC Jets
09-16-2020, 04:53 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, i feel once you get it up in the air those...

Gary, i feel once you get it up in the air those big ole gear doors will help slow the gear coming down.

if not, those adjustable flow valves festo has would be easy to install and adjust after...
Forum: RC Jets
09-14-2020, 05:44 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, why not just make a bubble from balsa...

Gary,
why not just make a bubble from balsa wood and then make some fiberglass moldings of the bubble. You can then cut a hole in the liner to clear the hinge and use the bubble to cover the hole.
Forum: RC Jets
09-08-2020, 08:40 PM
Replies: 978
Views: 200,484
Posted By invertmast

clippard has all sorts of Tee’s and such. I was...

clippard has all sorts of Tee’s and such. I was just looking a few days ago and they have 1/16” tee’s with a 3/32 or 1/8” inlet barb
Forum: RC Jets
09-07-2020, 07:49 PM
Replies: 978
Views: 200,484
Posted By invertmast

Looking good Gary. One question-gestion, why...

Looking good Gary.

One question-gestion, why not run a 4mm air line to that T fitting for the nose gear cylinders? That would provide more volume of air for the 2 cylinders to share, basically...
Forum: RC Jets
08-30-2020, 05:53 AM
Replies: 978
Views: 200,484
Posted By invertmast

gary, just incase it hasnt been suggested,...

gary,
just incase it hasnt been suggested, just flip the servo around. LOL
Forum: RC Jets
08-18-2020, 10:34 PM
Replies: 978
Views: 200,484
Posted By invertmast

Looking good Gary. Its a wonderful feeling when...

Looking good Gary. Its a wonderful feeling when things start flapping on their own!
Forum: RC Jets
06-23-2020, 08:56 PM
Replies: 978
Views: 200,484
Posted By invertmast

i agree completely! With some cad programs, you...

i agree completely! With some cad programs, you can do draft analysis and it’ll show you exactly where the problems. Your tank while fairly simple does have some complex area’s as you have found...
Forum: RC Jets
06-23-2020, 03:29 PM
Replies: 978
Views: 200,484
Posted By invertmast

That tank looka great, i’ll send some T38 tank...

That tank looka great, i’ll send some T38 tank plugs for you to make some tanks out of. Lol
Forum: RC Jets
06-06-2020, 04:46 AM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, the 3733 style 6oz is very easy to work...

Gary,
the 3733 style 6oz is very easy to work with. Its a slightly looser weave, but it conforms over curves extremely well.

one thing you can try to help keep things down, is to apply the...
Forum: RC Jets
06-05-2020, 02:09 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, one think you can do that i have done...

Gary,
one think you can do that i have done that works well. Layup a tank half that goes just past the centerline of the tank and leave it to cure. Once it cures, remove the tank half, trimmed...
Forum: RC Jets
05-31-2020, 05:20 AM
Replies: 978
Views: 200,484
Posted By invertmast

I would probly do 2 layers of 3.16oz style...

I would probly do 2 layers of

3.16oz style 220

2 layers of

5.8oz style 3733

following my a final layer of the style 220.
Forum: RC Jets
05-29-2020, 07:29 PM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, you need to use a perforated plastic...

Gary,
you need to use a perforated plastic between the peel ply and breather fabric. You can use get some cheap, thin plastic sheet from the local home depot, walmart etc and just go Michael...
Forum: RC Jets
05-27-2020, 05:54 AM
Replies: 978
Views: 200,484
Posted By invertmast

I think you’ll be fine with what you have...

I think you’ll be fine with what you have currently. You really only need as much surface area for the inlets as the compressor has surface area as the jet efflux and the turbine itself will suck...
Forum: RC Jets
02-07-2020, 05:51 AM
Replies: 978
Views: 200,484
Posted By invertmast

Gary, i would remove an area of the top glass...

Gary,
i would remove an area of the top glass and the foam down to the bottom layer of glass, then fill in this hockey puck shapes indentation with hysol. Allow to cure, sand flush and now you...
Forum: RC Jets
09-16-2019, 05:06 PM
Replies: 978
Views: 200,484
Posted By invertmast

that is pretty cool! I guess i need to just...

that is pretty cool! I guess i need to just make the plunge and make the switch to Jeti on all my stuff
Forum: RC Jets
09-16-2019, 09:03 AM
Replies: 978
Views: 200,484
Posted By invertmast

That is Awesome Gary! is this Lua program...

That is Awesome Gary!

is this Lua program just a download addon to the jeti Tx?
Forum: RC Jets
09-13-2019, 06:36 PM
Replies: 978
Views: 200,484
Posted By invertmast

That is awesome! I had thoughts on doing...

That is awesome! I had thoughts on doing something like this on the F14 for the auto spoiler deploy on landing. Its nice to see that its possible and just another reason for me to switch to Jeti.
Showing results 1 to 25 of 41
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.